FLOW SB FO E PL CI WPA SR

FLOW SB FO E PL CI WPA SR

CE EN ISO 20345:2022

3R022E

Low safety shoe

36-47

Size guide

Description

Toecap: 200J polymeric composite non-thermic
Upper: Suede leather 1,8-2,0 mm and PU coated anti-scratch leather Hydro
Midsole: PL certified antiperforation dielectric composite fabric
Insole: Dielectric insulating foam open-cell polyurethane extra comfort
Sole: PU Dielectric/Outsole, PU Dielectric/Midsole, PU Dielectric/Upper sole
Other: 20.000V Sole Insulation (ASTM 2413-11, C.S.A. Z195-14, INSULATING SOLE FROM 1.000 M), Extra Perspiration, Anti-torsion sole shank

Technical documents

FLOW SB FO E PL CI WPA SR

36-47

Description and further information

Low safety shoe, suede back leather and WPA anti-scratch leather thickness 1,8-2,0 mm.
Perspiring and abrasion resistant fabric lining.
Soft, lined and padded tongue.
COMPLETELY METAL FREE SHOE

TOECAP 200J polymeric composite non-thermic according to EN 22568
PL MIDSOLE flexible antiperforation composite fabric according to EN 22568
SOLE 3 RUN three-densities polyurethane dielectric, to hydrocarbons and to abrasion, anti-shock and anti-slipping
Article 3R022E has been tested using a method analogous to ASTM F2413-18 (EH) and CSA Z195-14: determination of resistance to an electric shock, increase 1 kV/sec, voltage 20,000 V/60 Hz holding the voltage for 1 minute. Electrical current requirement below 1.0 mA.
The outsole of the footwear, within specific limits (in the absence of moisture, not referring to the upper), was tested using a method analogous to EN ISO 20345:2022 to provide electrical insulation against voltages up to 1000 V M ohm >1000.
(Test report No. 4314043.01/E)
ANTI TORSION insert in the sole to assure stability on uneven ground
DIELECTRIC INSOLE, extracomfort bimaterial with activated carbon, removable, anatomic, absorbing, antistatic, perspiring insulating and antibacterial.
Eco-Friendly
FO sole resistance to hydrocarbons
E energy absorption on seat region
PL antiperforation midsole
CI cold insulation of sole complex -17Ã‚Â°C
SR Slip resistance
THIS PRODUCT COMPLIES WITH THE REQUIREMENTS OF THE STANDARD ASTM F2413-24:
- Impact resistant footwear (I)
- Compression resistant footwear (C)
- Puncture Resistant Footwear (PR)
- Electric Hazard Resistant Footwear (EH)
- Slip Resistance (SRO)
Size 36-47 Shoe weight Sz 42 gr 550

Size guide

Comparison table of measurements

EUROPA	UK	US	MILLIMETERS	INCHES
35	2,5	3,5	225	8,9
36	3	4	232,5	9,2
37	4	5	240	9,5
38	5	6	247,5	9,7
39	6	7	255	10
40	6,5	7,5	262,5	10,3
41	7	8	270	10,6
42	8	9	277,5	10,9
43	9	10	285	11,2
44	10	11	292,5	11,5
45	10,5	11,5	300	11,8
46	11	12	307,5	12,1
47	12	13	315	12,4
48	13	14	322,5	12,7
49	14	15	330	13

See anti-slip results

ANTI-SLIP RESULTS

Anti-slip performance testing

Ceramic tile floor with NaLS

Forward Heel
(heel slip 7°)

≥ 0.31

≥ 0.44

Backward heel
(heel slip 7°)

≥ 0.36

≥ 0.44

Ceramic tile floor with glycerin

Forward Heel
(heel slip 7°)

≥ 0.19

≥ 0.24

Backward heel
(heel slip 7°)

≥ 0.22

≥ 0.24

Recommended areas of use

Cold Environments

Electrician

Certifications applied

Heel Energy Absorption

Certifications

Heel Energy Absorption

Footwear with energy absorption in the heel to reduce impact while walking. Enhances comfort and protects joints in demanding work environments.

ASTM F2413-24

Certifications

ASTM F2413-24

ASTM F2413-+E18:E6924 specifies the safety, performance, and protective requirements that safety footwear must meet according to U.S. standards.

Insulation up to 20,000V

Certifications

Insulation up to 20,000V

Dielectric soles insulated up to 20,000 V, designed to shield the operator from high-voltage electric discharges in electrical or industrial work environments.

Water Penetration and Absorption (WPA)

Certifications

Water Penetration and Absorption (WPA)

The upper material is tested to resist water penetration, keeping feet dry even in wet or rainy environments.

PL Puncture Resistance with Non-Metallic Insert (nail Ø 4.5mm)

Certifications

PL Puncture Resistance with Non-Metallic Insert (nail Ø 4.5mm)

Anti-perforation plate inserted in the sole to protect the foot from sharp objects and punctures, ensuring safety in hazardous work environments. PL puncture resistance with non-metallic insert (nail Ø 4.5mm)

Hydrocarbon Resistance

Certifications

Hydrocarbon Resistance

Footwear resistant to hydrocarbons, designed to maintain the properties of the sole when in contact with oils and fuels. Ideal for industrial environments and workshops.

Slip Resistance (mandatory ceramic-Nals test)

Certifications

Slip Resistance (mandatory ceramic-Nals test)

According to EN ISO 20345:2022, slip resistance is a mandatory requirement and is tested on a ceramic surface contaminated with sodium lauryl sulfate (NaLS) solution. This test, stricter than previous versions, simulates real slipping conditions and ensures that all certified safety footwear provides a minimum level of grip. The SRA, SRB, and SRC classifications have been removed in the new regulation, making the NaLS ceramic test the standard.